Grade 80

Code: 443 Chain Sling Selection
The maximum working load limit for each size of chain is shown. These ratings are based on ideal conditions, however in practice, working conditions may vary widely. All lifting applications should be assessed by a competent person in order to establish the size and type of sling required.

MULTI-LEG SLING ANGLE

In the case of multi-leg slings, the angle between the legs is critical. The actual tension on each leg increases as shown in the diagram opposite. For this reason all general purpose chain slings are given a rating based upon use at a range of angles up to 45° to the vertical. A reduced rating is also given for use in the range of anglesbetween 45-60°. Chain Slings should never be used at angles greater than 60° to vertical.

HEAD ROOM

The distance between the crane hook and the load is known as the "Head Room". If a specific head room is required, the "Reach" of the chain sling must increase as the angle between the legs increases as shown opposite.

SLING REACH

The reach of a chain sling is the distance between bearing points of the upper and lower terminal fittings. This distance, commonly known as the "Bearing to Bearing" should be quoted when ordering slings. Shortening clutches may be fitted to a sling, making the reach adjustable, hence increasing the versatility of the sling.

Enquire about this item
Code: 448 Coupling Pin and Sleeve Set

Replacement Pin and Sleeve Sets for all sizes of Yoke Connectors come packed together in a sealed bag.

Part Code

Chain Size (mm)

8-PO15-07

7 & 8

8-PO15-10

10

8-PO15-13

13

8-PO15-16

16

8-PO15-20

20

8-PO15-22

22

8-PO15-26

26

8-PO15-32

32

Enquire about this item
Code: 450 Grade 80 Barrel Hook BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

Enquire about this item
Code: 452 Grade 80 Bolt-on Lifting Point BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

W.L.L

tonnes

A

mm

B

mm

D

mm

F

mm

K

mm

H

mm

M

mm

L

mm

R

mm

Mass

Kg

8-058-1T

1.0

50

72

14

27

98

55

14

139

24

0.8

8-058-3T

3.0

58

84

17

33

114

50

16

144

29

1.1

8-058-5T

5.0

64

116

22

43

160

74

20

203

33

2.5

Enquire about this item
Code: 454 Grade 80 Clevis C Hook BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

A

mm

K

mm

P

mm

T

mm

H

mm

W.L.L.

Tonnes

Mass

Kg

8-097-07

7,8

9

80

19

18

22

2.0

0.5

8-097-10

10

11

105

26

24

26

3.15

0.9

8-097-13

13

14

138

34

32

34

5.3

2.1

8-097-16

16

18

170

38

37

45

8.0

3.6

Enquire about this item
Code: 456 Grade 80 Clevis Clutch BS EN1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

A

mm

B

mm

C

mm

D

mm

E

mm

F

mm

W.L.L.

Tonnes

Mass

Kg

8-060-07

7,8

8

9

10

9

16

62

2.0

0.4

8-060-10

10

12

12

14

12

25

87

3.15

0.9

8-060-13

13

16

17

17

15

32

115

5.3

2.1

8-060-16

16

20

20

19

19

39

143

8.0

3.2

8-060-20

20

21

23

23

22

46

152

12.5

5.0

Enquire about this item
Code: 458 Grade 80 Clevis Clutch Locking Type BS EN1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

A

mm

B

mm

C

mm

D

mm

E

mm

F

mm

W.L.L.

Tonnes

Mass

Kg

8-061-07

7,8

10

10

10

10

24

56

2.0

0.5

8-061-10

10

12

12

12

12

28

66

3.15

0.9

8-061-13

13

15

15

16

16

39

88

5.3

2.2

Enquire about this item
Code: 460 Grade 80 Clevis Grab Hook BS EN1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain 

Size mm

A

mm

P

mm

F

mm

K

mm

H

mm

L

mm

W.L.L. Tonnes

Mass

Kg

8-042-07

7,8

9

10

30

55

25

93

2.0

0.3

8-042-10

10

12

13

41

77

35

128

3.15

0.8

8-042-13

13

15

16

53

97

42

152

5.3

1.6

8-042-16

16

17

20

58

102

45

180

8.0

2.7

8-042-20

20

23

23

98

124

54

217

12.5

4.7

Enquire about this item
Code: 462 Grade 80 Clevis Self Locking Hook BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

A

mm

K

mm

P

mm

T

mm

H

mm

W.L.L.

Tonnes

Mass

Kg

8-026-07

7,8

9

119

34

20

24

2.0

0.8

8-026-10

10

11

143

44

26

30

3.15

1.4

8-026-13

13

14

179

52

30

39

5.3

2.9

8-026-16

16

18

212

60

36

49

8.0

5.6

8-026-20

20

21

243

90

48

62

12.5

8.8

8-026-22

22

24

273

80

49

63

15.0

12.8

Enquire about this item
Code: 464 Grade 80 Clevis Shackle BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

A

mm

K

mm

L

mm

W

mm

G

mm

M

mm

C

mm

W.L.L.

Tonnes

Mass

Kg

8-066-07

7,8

9

59

35

33

34

16

79

2.0

0.4

8-066-10

10

11

78

48

37

40

20

93

3.15

0.8

8-066-13

13

14

98

64

49

44

22

118

5.3

1.4

8-066-16

16

18

112

69

60

54

28

141

8.0

2.5

Enquire about this item
Code: 466 Grade 80 Clevis Skip Hook with Spring Gate BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

A

mm

K

mm

L

mm

W

mm

B mm

W.L.L. Tonnes

Mass Kg

8-069-13

13

14

141

57

65

125

5.3

1.8

Enquire about this item
Code: 468 Grade 80 Clevis Sling Hook BS EN1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

A

mm

K

mm

P1

mm

T

mm

H

mm

W.L.L.

Tonnes

Mass

Kg

8-043/S-07

7,8

9

98

27

18

22

2.0

0.8

8-043/S-10

10

11

121

34

23

29

3.15

1.4

8-043/S-13

13

14

147

44

30

37

5.3

2.9

8-043/S-16

16

18

166

48

39

42

8.0

5.6

8-043/S-20

18, 20

21

200

56

47

50

12.5

8.8

Enquire about this item
Code: 470 Grade 80 Closed Coupling Master Link BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

K mm

W

mm

T

mm

H

mm

L

mm

W.L.L.

Tonnes

Mass

Kg

8-052-07

7,8

100

50

15

15

78

2.0

0.3

8-052-10

10

127

65

19

19

101

3.15

0.7

8-052-13

13

145

72

23

22

113

5.3

1.1

8-052-16

16

174

80

25

26

137

8.0

1.7

8-052-20

20

202

104

31

36

165

12.5

3.0

Enquire about this item
Code: 472 Grade 80 Component Connector BS EN1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

K mm

A

mm

D

mm

B

mm

W.L.L.

Tonnes

Mass

Kg

8-015-07

7,8

57

18

9

22

2.0

0.2

8-015-10

10

68

25

11

26

3.15

0.3

8-015-13

13

91

30

16

35

5.3

0.7

8-015-16

16

100

36

19

38

8.0

1.1

8-015-20

20

122

42

22

46

12.5

1.7

8-015-22

22

152

49

24

59

15.0

3.0

8-015-26

26

162

55

30

62

21.2

4.6

8-015-32

32

202

69

36

79

31.5

8.6

Enquire about this item
Code: 474 Grade 80 Coupling Self Locking Hook BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Enquire about this item
Code: 476 Grade 80 Coupling Sling Hook BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

K

mm

P

mm

T

mm

H

mm

W.L.L.

Tonnes

Mass

Kg

8-055-07

7,8

93

30

19

23

2.0

0.4

8-055-10

10

115

36

23

31

3.15

0.9

8-055-13

13

141

42

28

36

5.3

1.8

8-055-16

16

166

47

32

45

8.0

3.0

8-055-20

20

191

52

43

48

12.5

4.7

Enquire about this item
Code: 478 Grade 80 Excavator Weld-on Hook BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

W.L.L

tonnes

P mm

L

mm

T

mm

H

mm

F

mm

W

mm

A

mm

M

mm

Mass

Kg

8-081-01

1.0

18

70

18

27

25

95

7

4

0.6

8-081-02

2.0

25

85

20

30

30

115

8

5

1.0

8-081-03

3.0

28

107

23

30

35

133

9

6

1.4

8-081-04

4.0

28

114

30

38

42

142

10

7

2.0

8-081-05

5.0

30

135

31

47

44

167

12

7

3.0

8-081-08

8.0

32

137

39

52

50

176

12

8

3.8

8-081-10

10.0

44

170

42

56

56

222

13

8

6.3

Enquire about this item
Code: 480 Grade 80 Eye Container Hook BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

Desc

K

mm

A

mm

F

mm

T

mm

G

mm

H

mm

W.L.L.

Tonnes

Mass

Kg

8-067-45LT

20

Left 45º

192

70

46

25

75

48

12.5

3.9

8-067-45RH

20

Right 45º

192

70

46

25

75

48

12.5

3.9

Enquire about this item
Code: 482 Grade 80 Eye Foundry Hook BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

K mm

P

mm

A

mm

D

mm

T

mm

H

mm

W.L.L.

Tonnes

Mass

Kg

8-047-07

7,8

122

61

24

12

20

30

2.0

0.7

8-047-10

10

150

74

31

15

24

34

3.15

1.3

8-047-13

13

180

88

40

20

34

42

5.3

2.4

8-047-16

16

215

98

49

24

43

50

8.0

4.0

8-047-20

20

248

112

60

28

46

57

12.5

6.8

Enquire about this item
Code: 484 Grade 80 Eye Grab Hook BS EN1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain 

Size mm

P

mm

A

mm

G

mm

K

mm

F

mm

W.L.L.

Tonnes

Mass

Kg

8-041-07

7/8

10

15

9

60

30

2.0

0.3

8-041-10

10

13

20

13

84

41

3.15

0.6

8-041-13

13

16

25

15

102

52

5.3

1.4

8-041-16

16

20

30

20

114

57

8.0

2.3

8-041-20

20

23

36

24

132

73

12.5

3.9

8-041-22

22

26

38

26

165

70

15.0

4.8

8-041-26

26

29

41

32

187

100

21.2

10.5

8-041-32

32

37

57

40

230

90

31.5

19.4

No reduction on working load limit thanks to supporting wings which prevent chain link deformation.

Enquire about this item
Code: 486 Grade 80 Eye Self Locking Hook BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size

K

mm

P

mm

A

mm

D

mm

T

mm

H

mm

W.L.L.

Tonnes

Mass

Kg

8-025-07

7,8

136

34

25

11

20

24

2.0

0.8

8-025-10

10

167

44

32

13

26

30

3.15

1.4

8-025-13

13

207

52

40

16

30

39

5.3

2.9

8-025-16

16

252

60

52

21

36

49

8.0

5.7

8-025-20

20

282

90

64

23

48

62

12.5

8.5

8-025-22

22

319

80

70

24

49

63

15.0

12.5

8-025-26

26

343

99

80

25

56

69

21.2

14.5

8-025-28

28

401

120

90

28

63

81

25.0

24.9

Enquire about this item
Code: 488 Grade 80 Eye Sling Hook with Latch BS EN1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

K

mm

P1

mm

A

mm

D

mm

T

mm

H

mm

W.L.L.

Tonnes

Mass

Kg

8-044/S-07

7,8

98

28

25

11

20

23

2.0

0.8

8-044/S-10

10

121

36

32

14

23

31

3.15

1.4

8-044/S-13

13

152

40

40

18

28

38

5.3

2.9

8-044/S-16

16

184

44

50

22

32

47

8.0

5.6

8-044/S-20

20

218

45

60

26

43

48

12.5

8.8

8-044/S-22

22

244

73

50

31

50

62

15

12.8

8-044/S-26

26

279

77

64

35

60

80

21.2

13.6

8-044/S-32

32

352

114

88

40

65

86

31.5

18.7

Enquire about this item
Code: 490 Grade 80 Half Coupling Link with Coupling Pin & Sleeve Set

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

L

mm

A

mm

D

mm

K

mm

W.L.L.

Tonnes

Mass

Kg

8-054-07

7,8

28

18

9

22

2.0

0.1

8-054-10

10

34

25

11

26

3.15

0.2

8-054-13

13

45

30

16

35

5.3

0.4

8-054-16

16

50

36

19

38

8.0

0.6

8-054-20

20

60

42

22

46

12.5

1.1

8-054-22

22

76

49

24

59

15.0

1.7

8-054-26

26

80

55

30

62

21.2

2.7

Enquire about this item
Code: 492 Grade 80 Insulated Blank Swivel with Ball Bearing BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

Insulated Blank Swivels with ball bearing are individually tested to resist 1500 volts.

Designed for protection of overhead crane during welding operations on suspended loads.

SPECIFICATIONS

Part

Code

Chain

Size mm

D

mm

L

mm

W.L.L. Tonnes

Mass

Kg

8-088-07

7,8

50

75

2.0

0.5

8-088-10

10

62

94

3.15

1.1

8-088-13

13

77

123

5.3

2.3

8-088-16

16

94

143

8.0

4.2

8-088-20

20

109

164

12.5

6.4

Enquire about this item
Code: 494 Grade 80 Lifting Chain

Hackett Grade 80 Lifting Chain is manufactured from alloy steel and complies fully with EN818-2.

Only chain fully compliant with all aspects of EN818-2 can be used in chain slings certified to EN818-4.

Hackett Grade 80 lifting chain is embossed MA8 and also with class leading batch code marking. The chain is proof load tested to 2.5 times working load limit and is supplied in a black painted finish. The Hackett Grade 80 chain is suitable for use in a temperature range of -40C up to 200C without reduction in working load limit, reductions apply up to 400C.

Part code

Chain Size

mm

A mm

B mm

C mm

WLL Tonnes

Kgs per

metre

AS1.070.5

7

7

21

25.9

1.5

1.1

AS1.080.5

8

8

24

29.6

2.0

1.5

AS1.100.5

10

10

30

37.0

3.15

2.2

AS1.130.5

13

13

39

48.1

5.3

3.8

AS1.160.5

16

16

48

59.2

8.0

5.8

AS1.200.5

20

20

60

74.0

12.5

9.1

AS1.220.5

22

22

66

81.4

15.0

11.0

AS1.260.5

26

26

78

96.2

21.2

15.3

AS1.320.5

32

32

96

118.0

31.5

23.2

Enquire about this item
Code: 497 Grade 80 Master Link EN1677-4

Hackett Grade 80 Master Links are manufactured from alloy steel  in accordance with EN1677-4. All Master Links are individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit, reductions apply up to 400C.

TECHNICAL SPECIFICATION

Master Link for single and double leg chain slings

Part 

Code

Chain Size mm

Single

Chain Size mm

Double

mm

mm

mm

W.L.L. Tonnes

Mass 

Kg

X-003-0806

6, 7 & 8

6

13

110

60

2.8

0.4

X-003-1008

10

7&8

16

140

70

4.2

0.6

X-003-1310

13

10

20

160

90

6.7

1.2

X-003-1613

16

13

25.5

200

110

11.8

2.4

X-003-2016

20

16

32

270

140

17.0

5.0

X-003-2220

22

20

36

282

153

22.7

6.8

X-003-2622

26

22

40

280

155

30.1

8.5

HA3226ML

32

26

50

360

190

36.0

16.6

HA3632ML

36

32

60

410

220

48.0

28.0

OVERSIZE MASTER LINKS FOR SINGLE AND DOUBLE LEG CHAIN SLINGS

Part

Code

Chain Size mm

Single

Chain Size mm

Double

A mm

B

mm

C

mm

W.L.L.

Tonnes

Mass

Kg

HA22ML

-

10

22

270

140

5.8

2.3

HA25ML

16

13

25

270

140

8.83

3.1

Enquire about this item
Code: 501 Grade 80 Omega Link BS EN1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain 

Size mm

K

mm

D

mm

T

mm

P

mm

W.L.L.

Tonnes

Mass

Kg

8-018-07

7,8

36

27

11

9

2.0

0.2

8-018-10

10

44

32

15

12

3.15

0.4

8-018-13

13

55

42

17

16

5.3

0.9

8-018-16

16

69

50

22

18

8.0

1.5

Enquire about this item
Code: 503 Grade 80 Open Coupling Master Link BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

K

mm

W

mm

T

mm

H

mm

A

mm

W.L.L.

Tonnes

Mass

Kg

8-051-07

7,8

100

50

15

15

15

2.0

0.3

8-051-10

10

127

65

19

19

19

3.15

0.7

8-051-13

13

145

72

23

22

25

5.3

1.0

8-051-16

16

174

80

25

26

30

8.0

1.6

8-051-20

20

204

104

31

36

36

12.5

3.0

Enquire about this item
Code: 505 Grade 80 Reevable Egg Link BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain Size mm

A

mm

K

mm

L

mm

G mm

T

mm

H

mm

W.L.L.

Tonnes

Mass

Kg

8-059-07

7,8

9

99

80

65

15

15

2.0

0.4

8-059-10

10

11

125

100

80

19

18

3.15

0.8

8-059-13

13

14

168

136

108

25

22

5.3

1.5

8-059-16

16

18

198

158

124

27

26

8.0

2.4

Enquire about this item
Code: 507 Grade 80 Round Sling Coupling BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

K

mm

W

mm

A

mm

B

mm

W.L.L.

Tonnes

Mass

Kg

8-053-07

7,8

33

40

18

24

2.0

0.2

8-053-10

10

42

47

25

29

3.15

0.4

8-053-13

13

51

53

30

35

5.3

0.7

8-053-16

16

63

67

36

44

8.0

1.3

8-053-20

20

71

80

42

52

12.5

2.1

8-053-22

22

112

125

49

72

15.0

5.7

8-053-26

26

130

150

55

84

21.2

9.1

Enquire about this item
Code: 509 Grade 80 Shortening Clutch with Half Link BS EN1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

A

mm

C

mm

D

mm

E

mm

F

mm

H

mm

G

mm

K

mm

W.L.L.

Tonnes

Mass

Kg

8-078-07

7,8

12

20

10

23

70

22

9

128

2.0

0.7

8-078-10

10

13

26

12

29

87

26

11

154

3.15

1.3

8-078-13

13

15

33

16

37

115

36

15

203

5.3

2.8

8-078-16

16

21

39

19

46

143

39

19

248

8.0

5.2

Enquire about this item
Code: 511 Grade 80 Sub Assemblies EN1677-4

Hackett Grade 80 components are manufactured from alloy steel  in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit, reductions apply up to 400C.

TECHNICAL SPECIFICATION

Part

Code

Chain Size

mm

A

mm

B

mm

C

mm

D

mm

E

mm

F

mm

W.L.L.

Tonnes

Mass

Kg

X-007-06

6

16

140

70

13

110

60

4.2

1.3

X-007-08

7&8

20

160

90

16

140

70

6.7

2.5

X-007-10

10

25.5

200

110

20

160

90

11.8

5.0

X-007-13

13

32

270

140

26

200

110

17.0

10.0

X-007-16

16

40

280

155

32

270

140

30.1

18.6

X-007-20

20

50

350

195

40

280

155

33.6

33.7

HA22SA

22

50

350

190

40

140

80

43.1

27.5

HA26SA

26

60

410

220

45

165

90

50.0

44.0

HA32SA

32

70

450

250

50

195

100

70.0

65.4

OVERSIZE SUB ASSEMBLIES FOR USE WITH 3 & 4 LEG CHAIN SLINGS

Part

Code

Chain Size

mm

A

mm

B

mm

C

mm

D

mm

E

mm

F

mm

W.L.L.

Tonnes

Mass

Kg

HA23QA

7 & 8

22

270

140

16

120

60

5.8

3.7

HA25QA

10

25

270

140

20

140

70

8.83

5.3

Enquire about this item
Code: 514 Grade 80 Swivel Self Locking Hook – Brass Bushing BS EN1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

K

mm

P

mm

B

mm

A

mm

D

mm

T

mm

H

mm

W.L.L.

Tonnes

Mass

Kg

8-027-06

6

149

29

22

31

12

15

19

1.12

0.7

8-027-07

7,8

186

34

29

36

14

20

24

2.0

1.2

8-027-10

10

220

44

34

40

16

26

30

3.15

2.0

8-027-13

13

267

52

43

46

22

30

39

5.3

4.2

8-027-16

16

328

60

50

60

24

36

49

8.0

7.3

8-027-20

20

388

90

82

75

26

48

62

12.5

11.4

8-027-22

22

457

80

95

97

33

49

63

15.0

18.1

Enquire about this item
Code: 516 Grade 80 Swivel Self Locking Hook with Ball Bearing BS EN1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

K

mm

P

mm

B

mm

A

mm

D

mm

T

mm

H

mm

W.L.L.

Tonnes

Mass

Kg

8-027N-07

7,8

186

34

29

36

14

20

24

2.0

1.2

8-027N-10

10

220

44

34

40

16

26

30

3.15

2.0

8-027N-13

13

267

52

43

46

22

30

39

5.3

4.2

8-027N-16

16

328

60

50

60

24

36

49

8.0

7.3

8-027N-20

20

388

90

82

75

26

48

62

12.5

11.4

8-027N-22

22

457

80

95

97

33

49

63

15.0

18.1

8-027N-26

26

535

99

115

123

42

56

69

21.2

29.5

This hook is designed to fully swivel while in use lifting a load

Enquire about this item
Code: 518 Grade 80 Swivel Sling Hook with Ball Bearing BS EN1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

Chain

Size mm

K

mm

P

mm

B

mm

A

mm

D

mm

T

mm

H

mm

W.L.L.

Tonnes

Mass

Kg

8-049N-07

7,8

155

26

27

36

12

18

22

2.0

0.9

8-049N-10

10

189

36

37

41

16

23

29

3.15

1.6

8-049N-13

13

233

42

40

46

21

28

35

5.3

3.2

8-049N-16

16

280

50

50

60

22

35

44

8.0

5.3

8-049N-20

20

356

56

82

74

25

49

65

12.5

9.2

This hook is designed to fully swivel while in use lifting a load

Enquire about this item
Code: 520 Grade 80 Swivel Sling Hook with Brass Bushing BS EN1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

DIMENSIONAL SPECIFICATIONS

Part 

Code

Chain 

Size mm

K

mm

P

mm

B

mm

A

mm

D

mm

T

mm

H

mm

8-049-07

7,8

155

26

27

36

12

18

22

8-049-10

10

189

36

37

41

16

23

29

8-049-13

13

233

42

40

46

21

28

35

8-049-16

16

280

50

50

60

22

35

44

8-049-20

20

356

56

82

74

25

49

65

This hook is designed not to swivel while in use lifting a load

TECHNICAL SPECIFICATIONS

Part 

Code

Chain 

Size mm

W.L.L.

tonnes

Proof

Load kN

M.B.L.

kN

Mass

Kg

8-049-07

7,8

2.0

49.0

78.4

0.9

8-049-10

10

3.15

77.2

123.0

1.6

8-049-13

13

5.3

130.0

208.0

3.2

8-049-16

16

8.0

196.0

314.0

5.3

8-049-20

20

12.5

306.0

490.0

9.2

Enquire about this item
Code: 522 Grade 80 Weld On Load Ring BS EN 1677-1

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part Code

W.L.L tonnes

A mm

B mm

C mm

D mm

E mm

F mm

L mm

M mm

a

b

Mass Kg

8-082-04

4.0

66

14

30

48

65

70

135

76

45

5

0.7

8-082-06

6.7

85

20

39

60

89

91

171

98

45

5

1.5

8-082-10

10.0

95

21

46

65

100

100

196

106

45

6.5

2.4

8-082-16

16.0

127

30

57

90

130

136

263

149

45

8

5.5

8-082-30

31.5

178

42

78

130

160

195

375

213

45

15

15.8

Enquire about this item
Code: 526 Grade 80 Weld-on Lifting Point BS EN 1677-1+2

The William Hackett Grade 80 forged lifting components are manufactured by YOKE from alloy steel in accordance with EN1677. All forged components are individually magnaflux crack detected after heat treatment, they are then individually proof load tested to 2.5 times working load limit in accordance with EN1677. Only components fully compliant with all aspects of EN1677 can be used in chain slings certified to EN818-4. The William Hackett Grade 80 lifting components are suitable for use in a temperature range of -40C up to 200C without reduction in working load limit.

SPECIFICATIONS

Part

Code

W.L.L

Tonnes

W

mm

D

mm

F

mm

K

mm

H

mm

R

mm

L

mm

Mass

Kg

8-057-1T

1.0

50

14.2

27

38

55

24

105

0.5

8-057-3T

3.0

58

17.2

34

48

60

29

112

0.9

8-057-5T

5.0

64

22.5

43

61

74

33

154

1.8

8-057-8T

8.0

61

27.8

54

73

82

34

169

2.6

8-057-10T

10.0

75

30.8

54

73

103

41

191

3.0

8-057-15T

15.0

91

37.5

70

93

123

50

234

6.3

Enquire about this item
Code: 528 Latch Kits for Excavator Weld On Hook

Yoke Replacement Latch Kits to suit Excavator Weld On Hooks come complete with tension spring and nut and bolt for quick and easy replacement.

Part Code

Size (tonnes)

8-P081-01

1.0

8-P081-02

2.0

8-P081-03

3.0

8-P081-04

4.0

8-P081-05

5.0

8-P081-08

8.0

8-P081-10

10.0

Enquire about this item
Code: 530 Latch Kits to suit Grade 80 Clevis and Eye Sling Hooks

Yoke Replacement Latch Kits to suit both Clevis and Eye Sling Hooks come complete with tension spring and nut and bolt for easy replacement.

Part Code

Chain Size mm

8-P044-07

7, 8

8-P044-10

10

8-P044-13

13

8-P044-16

16

8-P044-20

20

8-P044-22

22

8-P044-26

26

8-P044-32

32

Enquire about this item
Code: 532 Latch Kits to suit Grade 80 Swivel Sling Hooks

Yoke Replacement Latch Kits to suit both Swivel Sling Hooks come complete with tension spring and nut and bolt for quick and easy replacement.

Part

Code

Chain Size

mm

8-P044-07

7, 8

8-P044-10

10

8-P044-13

13

8-P044-16

16

Enquire about this item
Code: 534 Load Pin Kits

Replacement Load Pin Kit Sets for all sizes of Yoke Clevis Hooks come packed together in a sealed bag and come with a spare retaining pin in case one retaining pin is lost.

Part Code

Chain Size

8-PO26-07

7 & 8

8-PO26-10

10

8-PO26-13

13

8-PO26-16

16

8-PO26-20

20

Enquire about this item
Code: 536 Load Pin Kits to suit Yoke Clutch 8-078

Replacement Load Pin Kit Sets for all sizes of Yoke Shortening Clutch with Half Link come packed together in a sealed bag and come with a spare retaining pin in case one retaining pin is lost.

Part Code

Chain Size (mm)

8-P072-07

7 & 8

8-P072-10

10

8-P072-13

13

8-P072-16

16

 For Replacement Pin for the Half Coupling Link, please order a Coupling Pin and Sleeve Set

Enquire about this item
Code: 538 Trigger Kits to suit Clevis, Eye and Swivel Self Locking Hooks

 Yoke Replacement Trigger Kits to suit all Yoke Self Locking Hooks are supplied with five components to allow ease of fitting. Diagrammatic instructions are supplied with the Trigger Kit.

Part

Code

Chain Size

mm

8-P025-06

6

8-P025-07

7 & 8

8-P025-10

10

8-P025-13

13

8-P025-16

16

8-P025-20

20

8-P025-22

22

8-P025-26

26

Enquire about this item